Search results

Hi Guys, Long time no see. I expect a lot has changed since I was last here. Can a Picaxe read and decode the IBUS output from a Flysky receiver? Next question would be, Can Picaxe encode and write the IBUS? Thanks.

I've used pulsin for lots of my RC projects, with great success. It works fine as long as the program is not too long. Am I right in believing that I can't use the servo command because I'm using the pulsin command, something to do with internal timing. Is it possible to use multiple interrupts...

Hi Guys, I need to detect the water level in a sight glass for a model steam boat. I could use a probe fitted into the tank, but would prefer to clip 'something' onto the sight glass to detect water low level. The sight glass is 5mm o/d. Any idea what the 'something' could be? thanks TOF

Hi Guys, I have a 40x2 and a 20M2 talking to each other via URF radio units. If I program this 20M2 serout c.1, n9600_8, ("R05","R",b8,b4,b5,b6,b24,b4,b5,b6,b24,b8) 40X2 SerIn [800], radiorx, baud2, ("R05"),b10,b11,b12,b13,b14,b15,b16,b17,b18,b19,b20,b21 all works fine. but if I try to send...

Hi Guys, Picaxe 40x2 chip. What is the maximum cable length, that would still give a reliable signal at 9600baud? using shielded twisted pairs. TOF

Hi Guys, Has anyone managed to interface picaxe to this module? http://www.ebay.co.uk/itm/RGB-Matrix-LED-Screen-Module-Driver-Board-Full-color-8x8-Arduino-No-Dot-Matrix-/271969146694 It uses the i2c interface. I can't find a datasheet anywhere. thanks TOF

Hi Guys, With reference to my project, large miniature railway. http://www.picaxeforum.co.uk/showthread.php?28328-help-needed-with-I2C&highlight=railway I've been asked if the signals can be controlled by radio link, ie xbee. I have read the Xbee tutorial and datasheets. So I have a few...

Hi Guys, I've been asked to look into a project to control a minature steam railway signalling. I thought of using a number of 40x2 and 20x2 chips. Interfacing between the chips using the I2C bus. I've downloaded the tutorial and read it more than once. Is it feasable to think along these...

Hi Guys, Can someone tell me what I'm doing wrong? 08M2 pin C.0 to OLED display. also tried on C.1, with same result. location on oled is correct, the 'p' is displayed followed by the wrong characters. clear screen command not always working. add setfreq m4 but still the same. If I connect...

Hi Guys, 08m2 when I use the disconnect command, it's stopping serial output on pinC.4. c.0 is an led ;catalex mp3 player ; #Picaxe 08M2 SetFreq m8 'Must be set to 8mhz or 16mhz for Serout command to work at 9600 baud disconnect Init: pause 2500 'Required for proper operation after...

Hi Guys, Our model boat club is about to expand to Club 500 boat racing h**p://w*w.club500slipway.com/about.php Initially were looking for a way of timing up to 6 boats at the same time. Would also need penalty input. Has anyone made / used such a system? My thoughts are: use a 40x2 to do...

Hi Guys, expect this is easy, for those who know. Chip 20X2 OLED AXE 134Y Pin A.0 I've a program that switches between 4Mhz,8Mhz,16Mhz and 32Mhz. I can output to oled: @8Mhz serout a.0,N2400,(245,128,"sample 8Mhz") @16Mhz serout a.0,N1200,(245,128,"sample 16Mhz") I can't get 4 or 32...

Hi Guys, I see that Design Spark 7 has been released. h**p://www.rs-online.com/designspark/electronics/eng/page/designspark-pcb-home-page Has anyone tried it yet? Does it support the Picaxe library? thoughts? regards tof

Hi Guys, I have 3 AXE134Y Oled Moduals. The first one I purchased has started to fail. 10 locations have missing colums, another has a missing dot. I've output a screen test using CGRAM serout C.4, N2400, (254,120,31,31,31,31,31,31,31,31), to all locations. I can read the usually displayed...

I have put together this board to produce diesel engine noise for my model boat. It could be used for model lorries as well. control is by radio control receiver unit, linked to motor. I'll post pcb file for those that have the free RS program. The program file. picture of circuit board...

Hi Guys, I seem to remember that you could limit the number of automatic backups. Is this avaliable in V.6.0.7.3? TOF

Hi Guys, This has bugged me for some time. symbol pb4=c.5 symbol pb3=c.6 symbol pb2=c.7 symbol relay3=c.0 symbol relay2=c.1 symbol relay1=c.2 main: ;------------------------------------------- if pinc.5=1 then ; this works high relay1 high relay2 high relay3 endif...

Hi Guys, This is a project for one of my model boats. How can I replicate the sound of a diesel engine noise using an 08m2 picaxe. It needs to vary with the speed on the boat electric motor. the easy bit is reading via the serin command to detect the speed. the hard bit, which I'm struggling...

Hi Guys, Is there a better / easier way to program this. Its to show water level, sensed by sfr05. lower the distance, higher the level. Only showing relative parts. #picaxe 40x2 symbol oled=A.7 symbol baud=n2400 ;bargraph setup CGram serout oled,baud, (254,64,0,0,0,0,0,0,0,21) ;0...

Hi Guys, Before I put an order in for the chips, can you check my thinking please. I require 3 'pulsin' inputs, from a radio control unit. (from spare inputs on my model boat RC.) The pulse width of each input will determine what happens to a bank of relays and/or opto isolators. If I use...