Search results

Is it possible to program any of the picaxe micros :adc: down to as little as 50 millivolt levels ie the picaxe gives a different output for every step level change of 50mv either up or down..?

Just want to know which , if any, of the picaxe micros can do parallel tasking, ie more than 1 start block in the flowchart programming chart technique..

Wanting to program 20m2 device in flowchart, pre selecting ins and outs, but input c6 is greyed out in preselect programming screen,, but datasheet diagram indicates c6 is available as input, is c6 input available as a useable input or not? Regards Peter

is it possible to program a picaxe for voice recognition commands

is it possible to use the axe213 / rfa001 picaxe wireless link to output out of the receiver a bcd output when the transmitter sends the same bcd input, eg say I wanted to send a bcd value of 6 which is :abcd/1248 = 0110 from the transmitter to the receiver, can the receiver output 0110 ...

I have a project that needs to accurately read down to as low as 50mV in 50mV increments up to about 2 volts, for about 30 increments of 50mV.. How accurate can I go with the picaxe devices of 08m, 14m, 20m 28x2 and 40x2 and preferably not use an external resonator..

14 segment quad led display that uses the vk16k33 ic2 display driver.. Looking for a circuit that shows how to use a picaxe to display alphanumeric characters onto the display

Over here in australia , I can buy a quad led display unit 14 segment x 4, alpha-numeric, which has a vk16k33 led display driver , using the ic2 and scl and sda pins protocol .. Does anyone know how to connect and program a picaxe with the vk16k33 driver?

is it possible to program any picaxe with a suitable eeprom, that records and displays accumulated minutes and hours from an input..onto an oled.. the application is for an irrigation pump that might run for 6 hours one day, then 4 hours the next day, then 3 hours on day 3, etc etc..when the 5...

I have recently purchased the axe133y oled display kit, have put it together, the oled display displays the default picaxe www oled massage when it powers up, I have 100% successful communication with the 18m2 adaptor board on the rear of the oled board, I have tried the test picaxe program code...

reading other peoples threads for hassles getting picaxes to work with common lcds, i note that back in june 1,2008, member westaust55 moderator, wrote the following: "The picaxe manual has the wrong connections for the data pins ,( they are back to front ).. This has been raised by others in...

is there any circuit diagram and code listing available on the internet or revolution education website that makes interfacing between a picaxe device and any common lcd display successful , otherwise its not possible!!

do lcd displays work similar to a 4516 , you load bcd into the load input pins , take a pin high or low, and then the 4516 counts up or down from the loaded value, in other words does an lcd accept bcd data into either 4 or 8 inputs, then write/load data by taking another pin of the lcd high or...

is there anyone on the picaxe forum that has a DEFINITE,WILL WORK schematic diagram of a picaxe interfaced to an lcd display module , 16 x 2 character type, hitachi 44780 or its common equivalent, and also programming code, because as yet no one but no one has come up with a picaxe to lcd...

How is it possible,surely it is, to email photos and also flowcharts onto the forum for others to view?

can any of the picaxes be programmed to give any squarewave,50% duty cycle, at any frequency between 500 hz and 2500 hz?can anyone give any examples please.

When is the picaxe forum operating over the xmas break?

Which is the best picaxe to use to connect to and program an lcd display unit?

I have followed the instructions in the help files of pe6 to the letter of how to connect and program lcd displays with a picaxe 18m, but it doesnt work, keeps hiccupping on syntax errors, even before downloading to the picaxe 18m.. Has anyone been successful at connecting and programming an...

wanting to printout the flowchart diagrams, but my toshiba laptop running pe6 wont allow printing , comes up with font error message, not sure what that means, if it does print, most segments of the flowchart is missing from the printed page.. I have absolutely no problem with printing anything...