Recent content by Jacobsen

I am a beginner with the program: Picaxe VSM Is there anyone here who can help me file: circuit1.DSN engine, so I can test simuleringren. See attach: bl-motor_emf driver.jpg You are welcome to send the file at. E-mail: mjs AT nypost.dk Sincerely, Monie

Is there anyone here who has experience with the coder to create a BLDC motor in a Micro Controller. I am aware that there can be bought ready-BLDC controller. But I would like to work with such a controller. And to get good start then I have some questions below. Which PIC circuit must be...

Can someone please advise me of the command for SERVO code to running a RC motor. I'm using: PICAXE Program Editor Ver.5.2.0 With the following codes I would like to make a (power steering)/controller for this Speed Controller. Speed controller type: Brushless Motor Speed Controller HV-45A...

Question to PICAXE forum I'm trying to connect an electrical motor to a solarcell, as seen on the Schematics. Problem: When the suns intnesity degrades we need to aditionally control a mosfet by PWM to reduce the current draw on the solarcell. (DIP Regulating), and it almost works...

Regarding emergency stop. I´m looking for a way to instruct my IC to make an emergency shut down, and thereafter beeing able to switch the system on again using the very same button. Does any one here knows a smart way to do so i.e coding example or perhaps a link to such a code. Best regards...

I'm trying to make a program for the &quot;Hacker Master 48-0-Flight&quot; controller, which will be able to start and control a BLCD motor and function as a speed regulater with a potentiometer My Basic Code: <code><pre><font size=2 face='Courier'> 'Servo PulsOut for Master 48-0-Flight...

How do I make the control to a 3-Phase DC motor as shown in this example <A href='http://www.sunwind.dk/3PhaseBrushlessDCMotor.jpg' Target=_Blank>External Web Link</a> How do I write the Basic codes for control of the OA OB OC OD OE and OF inputs, enabling a PICAXE-28X 4 Mhz to control these...

I'm trying to round up to three decimals without any luck. Please see codes below. <code><pre><font size=2 face='Courier'> SYMBOL BattNomFloatVoltage = 1362 SYMBOL SenseAmp = w2 ;b4:b5 SYMBOL RestOprund = B10 DisplayLine3: SenseAmp= 93 ;= 4.50 Amp Byte = $94; Start Line 3...

Can anyone help me complete the following routine? A single push to a button switches LED ON ( IF pin0 = 1 THEN ) and remains like this untill button is pushed again, making LED go OFF. On same entry. NB. I tried doing it like this, at +5V in on leg 11 LED ON goes on Using: PICAXE-28X - 4Mhz...

With the sentence: &quot;IF Solar &lt;= 0 THEN NoSolar&quot; I would like to send the following message to the display &quot;No Solar&quot; Using HD44780 I have tried several options. And checked the datarecord for the display and <b> EEPROM. </b> But I haven' t been able to send the message...

As I'm using the variable &quot;w3&quot; in other places and have no further variables available, is it somehow possible to release a variable with a poke and peek commando? Hopefully that isn't a too stupid question!! Addresses : PICAXE-28X 16F873A = 112 : $50-$7F / $C0-$FF Symbol b20 =...

How do I get 2 decimals with the Basic codes below? I have put &quot;READADC10 3,w3&quot; to 10 bit to get a wider resolution I am using PICAXE-28X I have tried to insert the following text at the end of the codes, to make the second decimal appear in the display. Byte = w3 // 1 |...

I have acquired a Flow sensor, that reads &quot;READADC 3,w3&quot; Grundfos Direct Sensors Web-link: <A href='http://net.grundfos.com/doc/webnet/directsensors/images/pressurelow.pdf ' Target=_Blank>External Web Link</a> And these values from the flow sensor I would like to output on my...

How can I'm read the binary from PORTC pins? Using 2 CMOS type 4516 Picaxe-28x - use PortA how to convert the value of a byte contents to a 3 decimal ACII code represenation ? I Pic-Logicator 2001 I'm do cmd: ----Start : : : : : a=PORT ( Cell Detail- EXPRESSION ) ...

Can the anyone help my? I have gotten a readout on the value &#8221;RPMCounter&#8221; with the command: serout 7,T2400,(254,&quot;Speed: &quot;,#RPMCounter,&quot; rpm &quot;,255) Why 2 time &quot;serout! 1: main_loop:goto main_loop 2: interrupt:return The complete basic code is listed...