Recent content by chaymoss

AllyCat, inglewoodpete thank you for your advices Well, now I've got integers varies between 0 and 360°, I did nothing special just switching the program mode while uploading the program and switching it back to run mode, I also put it in the motor shaft for regulating its rotation. You can find...

AllyCat, thank you for your suggetion (I'm wondering what do you mean by easier hardware). Now, using the same program, when I turn the picaxe board back on after being off, and spinning the encoder, I get some values for a few seconds but then it displays zeros as shown below : I did try...

Hemi345, thank you for your response. Changing the baud rate and using the program down below : #picaxe 28X2 #terminal 9600 ; Serial rates for UART init: symbol AMT22_NOP = 0x00; SPI commands symbol AMT22_RESET = 0x60 symbol AMT22_ZERO = 0x70 #define NEWLINE...

inglewoodpete, AllyCat, thank you for your answers. So, I tried this code to send instructions MOSI and receive data MISO, however the terminal doesn't show anything. You can find the code down below #picaxe 28X2 #terminal 115200 ; Serial rates for UART ; * AMT22 Pin Connections ; * Vdd (5V)...

inglewoodpete thank you for your suggestion. Reading Using I2C with PICAXE, I need to consider 3 i2c details : *Slave address *Address size *Bus speed However, I couldn't find Slave address in the sensor's datasheet. I only found the checksum formula, should I use it as a slave address? Also...

Technoman, Aries, and PieM, thank you all for your help. Well, I'm not really used to picaxe programming, so I need some enlightenment for how to create a new function in Picaxe Software. Down below you'll find a function that I need to make in picaxe software : uint8_t spiWriteRead(uint8_t...

Hello everyone, Currently, I'm trying to program PICAXE-28X2 BASE SHIELD to detect an angular position of the motor using an absolute encoder, you can find below my program that I used. #picaxe 28X2 #terminal 115200 ;symbol Miso = pinC.5; define input switch symbol Sclk = C.0; define output pin...

After contacting the Technical Support of MicroE, they informed me that I shouldn't change the Vcc data jumper from 3.3V to 5V as shown in the images down below. So I should have kept the default position of the jumper. And finally, now the stepper motor is spinning using the last shared code...

I tried that, it didn't work

I used this code to try your suggestion #picaxe 28X2 main: let b0 = 0 ; set b0 value high B.2; ENABLE the driver high B.0; Direction of the spinning FOR b0 = 0 TO 500 high B.5 ; switch on output B.5/ST pause 1 ; wait 0.5 seconds low B.5 ; switch off output B.5 pause 1 ...

I tried using PWM signal as shown in the code below init: PWMOUT B.5, 199, 399 ; start pwm high B.2; ENABLE the driver high B.0; Direction of the spinning main: pwmduty B.5, 199 ; set pwm duty pause 500 ; pause 0.5 s pwmduty B.5,50 ; set pwm duty pause...

I'm not connecting it to any pin, I think it's an output from the driver, and I don't need it in my program

Now I tried to change the motor to another stepper motor 17HS4401 and still doesn't work

Yes I swapped them, but nothing has changed

Case 1 : I set the RESET pin to low in the program Case 2 I diconnected it from the picaxe board, Case 3 I connected it to GND But nothing works And in all cases the torque potentiometer is in mid way