The wheel encoder subject has been mentioned before. PICAXE has been said to be to slow for PID controlling of motors. I still want to try. I made a new thread in Electro Tech forum, but I know very well, that this forum has a lot of very clever persons. So I would ask you to have a look at:
<A...
Hi Jeremy
I am trying to copy your anemometer circuit <A href='http://www.rev-ed.co.uk/picaxe/forum/Topic.asp?topic_id=4544&forum_id=24&Topic_Title=Low%2Bpower%2BCounter%2B%252D%2Bworking%2Bversion&forum_title=No+new+posts+please%21+17' Target=_Blank>External Web Link</a>
I does only...
Is there an easy way to calculate an absolute difference?
For example:
B1 = 2
B2 = 1
B3 = B1-B2 'This equals 1
B1 = 1
B2 = 2
B3 = B1-B2 'I want this to equal 1 to
I have been experimenting with a wind vane based on an angle encoder made of LED's and photo resistors. I have learned a lot and want to share. <A href='http://www.ab-it.dk/Filer/Windvane.pdf' Target=_Blank>External Web Link</a>
Using grey readings on a binary pattern makes the pattern analog...
Hi all.
I got a problem. I made the circuit shown on this gif <A href='http://www.ab-it.dk/images/shift_with_flip_flop.gif' Target=_Blank>External Web Link</a>
I made a shift register of four flip-flops. I use it to turn on for LED's one at a time. At the same time a LDR gets power and sends its...
How do I measure signal strength from a radio receiver?
I build a little FM-radio transmitter that can transmit a tone generated by a 555 timer circuit. I can receive it by my clock radio. I want to build a receiver with a directional antenna. Then I want to measure signal strength to be able to...
I need help to read a datasheet.
I am building a light seeking robot inspired by a resent tread in this forum.
I want 08M to run L293B (H-bridge). For that purpose I need 4 digital outputs. I need to read LDR's via 1 ADC input. I need to read two or more contacts. Here I can us 1 ADC input as I...
I got one 18X serving as master and 08M serving as slave.
Now they work fine talking serin/serout via two lines. I even managed them to use interrupt to trigger communication so they won't have to spent time just listening for serin.
Then I realised, that I need 4 I/O's on the 08M in addition...
Hi there. I have just wired up my ds1307 serial clock to the PICAXE and a LCD-display. It works just like clockwork. Only problem is to display the time. From the datasheet I realised that seconds and minutes is torn up from bytes to bits. I'm sure someone has some lines of code that convert...
Before I found PICAXE I bought a QUASAR PROJECT KIT #3145 (QPK). It's a temperature data logger that uses 4 x DS1820. It sends data via serial port.
I want PICAXE to receive these data. QPK reads with higher accuracy. The old DS1820 cannot be read with readtemp12.
Problem is QPK uses DTR and RxD...
Hi -
I've been looking for a way to get as much out off tree pins on a 08M as possible. Without to much complexity.
The first idea was to read with to input pins and address with a third output pin. If output is low I can read sensor 1 and 2 and when output is high I can read sensor 3 and 4...
Hi there
I've got a MC14011BCP (a quad 2-input NAND Gate). I want to invert the output from a output-pin on 08M. Can I just do that, or should other components be involved?
Test of link
<A href='http://www.hqproducts.com/eng/products/electricity//page_1/artl_P.SUP.22-A' Target=_Blank>External Web Link</a>
Edited by - AllanBertelsen on 07/04/2006 16:34:15
Someone made a weather station project with a nice blue control box in UK. I saw it at a web-site the other day. Now I can't find it again. Can anybody help me? I'll remember to add it to my favourites this time.
I've got the experimenter board AXE090. A LCD 2x20 display and the firmware chip. I've got it all hooked up. It worked nicely. With the tree pushbuttons I manage to control some LED's via a menu.
But then I wanted to build a more advances system using EEPROM for menu texts and data. Suddenly I...